CCNP Enterprise Certification Exam Update:
Before the change:
CCNP Enterprise certification consists of the CCNP Enterprise core exam (350-401 ENCOR) plus a concentrated exam to actually obtain the CCNP Enterprise certification certificate.
Concentrated exams include 6 professional subjects (300-410 ENARSI, 300-415 ENSDWI, 300-420 ENSLD, 300-425 ENWLSD, 300-430 ENWLSI, 300-435 ENAUTO)
After September 20:
Starting September 20th, there are two major changes:
- A new exam subject will be added to the centralized exam: 300-440 ENCC
“This exam certifies a candidate’s knowledge of designing and implementing cloud connectivity, including architecture models, IPsec, SD-WAN, operation, and design.”
2. The CCNP Enterprise certification exam materials are fully updated! That is to say, the core exam and all centralized exam materials will have major changes. For specific changes, please pay attention to: https://learningnetwork.cisco.com/s/cisco-certification-roadmaps?tabset-268a8=1
CCNP Enterprise Best Exam Solution:
Now:
Use Latest CCNP Enterprise 350-401 certification dumps: https://www.leads4pass.com/350-401.html to help you practice before the exam and ensure that you pass the CCNP Enterprise core exam 100% successfully.
The latest CCNP Enterprise 350-401 certification dumps contain 1061 latest exam questions and answers, fully covering the core exam questions of Cisco CCNP Enterprise. Check the CCNP Enterprise exam material page to get any subject of 6 concentrated exams, and you can choose the “concentrated exam” you need according to your career plan Exam” material! Guaranteed to help you pass the exam with ease.
After September 20:
The Cisco certification exam project is always updated and iterated. This is a technological innovation and progress! leads4pass has been changing with Cisco’s changes from the beginning to the end, so the latest Cisco CCNP Enterprise certification exam materials will also be updated after September 20!
All candidates have instant access to the latest exam materials to help them practice easily and pass successfully!
The latest CCNP Enterprise exam materials are shared online:
| From | Core Exam Code | Concentration Exam Code |
| leads4pass | 350-401 | 300-410,300-415,300-420,300-425,300-430,300-435 |
CCNP Enterprise Core Exam Material: Latest 350-401 certification dumps exam questions online practice
| Number of exam questions | Online Download | Last update |
| 15 | 350-401 PDF | 350-401 dumps |
New Question 1:
Refer to the exhibit.
A. Configure switch port mode trunk on SW2.
B. Configure switchport nonegotiate on SW3
C. Configure channel-group 1 mode desirable on both interfaces.
D. Configure channel-group 1 mode active on both interfaces.
Correct Answer: C
SW2 is using PAgP and both member interfaces Gi0/0 and Gi0/1 are in state(I), which means they are not receiving any activity.
New Question 2:
Refer to the exhibit.
An engineer must configure an ERSPAN tunnel that mirrors traffic from Linux1 on Switch1 to Linux2 on Switch2. Which command must be added to the destination configuration to enable the ERSPAN tunnel?
A. (config-mon-erspan-dst-src)# erspan-id 172.16.10.10
B. (config mon erspan-dst-src)# erspan-id 110
C. (config-mon-erspan-dst-src)# no shut
D. (config-mon-erspan-dst-src)# origin ip address 172.16.10.10
Correct Answer: B
New Question 3:
Refer to the exhibit Which command must be applied to complete the configuration and enable RESTCONF?
A. ip http secure-server
B. ip http server
C. ip http secure-port 443
D. ip http client username restconf
Correct Answer: A
New Question 4:
Refer to the exhibit.
Traffic is not passing between SW1 and SW2. Which action fixes the issue?
A. Configure LACP mode on S1 to passive.
B. Configure switch port mode to ISL on S2.
C. Configure PAgP mode on S1 to desirable.
D. Configure LACP mode on S1 to active.
Correct Answer: C
New Question 5:
In a Cisco SD-Access fabric architecture, which of the following are valid device roles (Choose three.)
A. Control Plane Node
B. Access routing device
C. Edge Node
D. Border Node
E. Distributed Node
Correct Answer: ACD
New Question 6:
Refer to the exhibit.
An engineer must create a configuration that executes the show run command and then terminates the session when the user CCNP logs in. Which configuration change is required?
A. Add the access-class keyword to the username command
B. Add the access-class keyword to the aaa authentication command
C. Add the auto command keyword to the username command
D. Add the auto command keyword to the aaa authentication command
Correct Answer: C
The auto command causes the specified command to be issued automatically after the user logs in. When the command is complete, the session is terminated.
Because the command can be any length and can contain embedded spaces, commands using the auto command keyword must be the last option on the line. In this specific question, we have to enter this line username CCNP auto command show running-config.
New Question 7:
Refer to the exhibit.
After an engineer configures an EtherChannel between switch SW1 and switch SW2, this error message is logged on switch SW2.
Based on the output from SW1 and the log message received on Switch SW2, what action should the engineer take to resolve this issue?
A. Configure the same protocol on the EtherChannel on switch SW1 and SW2.
B. Connect the configuration error on interface Gi0/1 on switch SW1.
C. Define the correct port members on the EtherChannel on switch SW1.
D. Correct the configuration error on interface Gi0/0 switch SW1.
Correct Answer: A
In this case, we are using your EtherChannel without a negotiation protocol. As a result, if the opposite switch is not also configured for EtherChannel operation on the respective ports, there is a danger of a switching loop. The EtherChannel Misconfiguration Guard tries to prevent that loop from occurring by disabling all the ports bundled in the EtherChannel.
New Question 8:
Which statement about when you configure FlexConnect APs and you want to set up Cisco Centralized Key Management fast roaming is true?
A. FlexConnect groups are required for Cisco Centralized Key Management fast roaming to work with FlexConnect access points.
B. APs that are in the same FlexConnect group but associated with different WLCs support Cisco Centralized Key Management.
C. Cisco Centralized Key Management fast roaming among FlexConnect and non-FlexConnect access points is supported.
D. The FlexConnect access point must be in standalone mode to support Cisco Centralized Key Management.
Correct Answer: A
New Question 9:
Refer to the exhibit.
An engineer reconfigures the port channel between SW1 and SW2 from an access port to a trunk and immediately notices this error in SW1\’s log:
*Mar 1 09:47:22.245: %PM-4-ERR_DISABLE: bpduguard error detected on Gi0/0, putting Gi0/0 in err-disable state
Which command set resolves this error?
A. SW1(config-if)#interface G0/0 SW1(config-if)#no spanning-tree bpdufilter SW1(config-if)#shut SW1(config-if)#no shut
B. SW1(config-if)#interface G0/0 SW1(config-if)#no spanning-tree bpduguard enable SW1(config-if)#shut SW1(config-if)#no shut
C. SW1(config-if)#interface G0/0 SW1(config-if)#spanning-tree bpduguard enable SW1(config-if)#shut SW1(config-if)#no shut
D. SW1(config-if)#interface G0/1 SW1(config-if)#spanning-tree bpduguard enable SW1(config-if)#shut SW1(config-if)#no shut
Correct Answer: B
New Question 10:
Refer to the exhibit. An engineer must configure static NAT on R1 to allow users HTTP access to the web server on TCP port 80. The web server must be reachable through ISP 1 and ISP 2. Which command set should be applied to R1 to fulfill these requirements?
A. ip nat inside source static tcp 10.1.1.100 80 209.165.200.225 80 extendable ip nat inside source static tcp 10.1.1.100 80 209.165.201.1 80 extendable
B. ip nat inside source static tcp 10.1.1.100 80 209.165.200.225 80 ip nat inside source static tcp 10.1.1.100 80 209.165.201.1 80
C. ip nat inside source static tcp 10.1.1.100 80 209.165.200.225 80 ip nat inside source static tcp 10.1.1.100 8080 209.165.201.1 8080
D. ip nat inside source static tcp 10.1.1.100 80 209.165.200.225 80 no-alias ip nat inside source static tcp 10.1.1.100 80 209.165.201.1 80 no-alias
Correct Answer: A
the “extendable” keyword should be added if the same Inside Local is mapped to different Inside Global Addresses (the IP address of an inside host as it appears to the outside network). An example of this case is when you have two connections to the Internet on two ISPs for redundancy. So you will need to map two Inside Global IP addresses into one inside local IP address.
New Question 11:
Refer to the exhibit.
An engineer must modify the access control list EGRESS to allow all IP traffic from subnet 10.1.10.0/24 to 10.1.2.0/24. The access control list is applied in the outbound direction on the router interface GigabitEthernet 0/1. Which configuration command set will allow this traffic without disrupting existing traffic flows?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: D
New Question 12:
Refer to the exhibit.
Which Python code snippet prints the descriptions of disabled interfaces only?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: B
!= is the “Is not true operator” Think along these lines and B is clearly correct.
New Question 13:
If the AP power level is increased from 25 mW to 100 mW. what is the power difference in dBm?
A. 6 dBm
B. 14 dBm
C. 17 dBm
D. 20 dBm
Correct Answer: A
New Question 14:
Refer to the exhibit.
An engineer configures a new HSRP group. While reviewing the HSRP status, the engineer sees the logging message generated on R2. Which is the cause of the message?
A. The same virtual IP address has been configured for two HSRP groups
B. The HSRP configuration has caused a spanning-tree loop
C. The HSRP configuration has caused a routing loop
D. A PC is on the network using the IP address 10.10.1.1
Correct Answer: A
New Question 15:
What are two valid modes that Cisco Express Forwarding can operate in? (Choose two.)
A. Central CEF mode
B. Dense CEF mode
C. Sparse CEF mode
D. Distributed CEF mode
E. Routed CEF mode
Correct Answer: AD
CEF can be enabled in one of two modes:
Central CEF mode – When CEF mode is enabled, the CEF FIB and adjacency tables reside on the route processor, and the route processor performs the express forwarding. You can use CEF mode when line cards are not available for CEF switching, or when you need to use features not compatible with distributed CEF switching.
Distributed CEF (dCEF) mode – When dCEF is enabled, line cards maintain identical copies of the FIB and adjacency tables. The line cards can perform the express forwarding by themselves, and this relieves the main processor – Gigabit Route Processor (GRP) – of involvement in the switching operation. This is the only switching method available on the Cisco 12000 Series Router.
https://www.cisco.com/c/en/us/support/docs/routers/12000-series-routers/47321-ciscoef.html
…
Check out the latest 350-401 certification dumps: https://www.leads4pass.com/350-401.html, and get 1061 latest exam questions and answers.
CCNP Enterprise Concentration Exam Materials:
| Concentration Exam: | Online Download: | Online Practice: |
| implementing Cisco Enterprise Advanced Routing and Services (ENARSI) | 300-410 PDF | 300-410 Dumps |
| Implementing Cisco SD-WAN Solutions (ENSDWI) | 300-415 PDF | 300-415 dumps |
| Designing Cisco Enterprise Networks (ENSLD) | 300-420 PDF | 300-420 dumps |
| Designing Cisco Enterprise Wireless Networks (ENWLSD) | 300-425 PDF | 300-425 dumps |
| Implementing Cisco Enterprise Wireless Networks (ENWLSI) | 300-430 PDF | 300-430 dumps |
| Automating and Programming Cisco Enterprise Solutions (ENAUTO) | 300-435 PDF | 300-435 dumps |
Candidates who took the CCNP Enterprise certification exam by September 20 can use this updated exam material to help you pass the exam with ease!
After September 20th, you can use the latest updated CCNP Enterprise certification exam materials! leads4pass CCNP Enterprise certification exam materials are updated throughout the year to ensure instant validity.